Pre-Order

ESM303H - Motorized Test Stand(Horizontal)

Attribute:

"MARK-10" (Made in USA) Horizontal Motorized Test Stand, 18.0 in (457 mm) travel and Load capacity 300 lbF (1.5 kN) I Model ESM303H

Share

Brand : MARK-10

Share

Horizontal Motorized Tension / Compression Test Stand.

Model : ESM303H 

Brand : Mark-10 (Made in U.S.A.)

The ESM303H is a highly configurable horizontal force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMe™ force-based positioning – using your hand as your guide, push and pull on the load cell to move the crosshead at a variable rate of speed.

With generous travel, clearance, and depth dimensions, a wide range of tests can be performed, including break testing, cycling, limit testing to a load or distance, loadholding, elongation testing, tensile testing, compression testing, and more. Satisfy various test methods through an easy-to-use menu, allowing the configuration of test speed, force and distance limits, cycling, preload, and many other functions, all protected by a password. Save up to 50 profiles to accommodate a range of test methods.

When the ESM303H’s clearance is insufficient for the application, its modular mechanical design allows for frame extensions. Modularity extends to the controller functions as well. Individual functions, such as travel measurement, cycling, loadholding, etc., may be purchased either upfront or enabled in the field through an activation code. This a-la-carte platform allows for custom configuration as appropriate for the application and budget.

Collect force and travel data, plot and analyze the results, and control test stand motion via PC-based MESUR®gauge Plus software. Or, fully control the stand by a PC through a custom-written program in any language supporting ASCII communications.

Standard Features

  • Selectable speed setting
  • Right and left travel limit switches
  • Adjustable, removable control panel may be mounted to the left or right end of the frame
  • Password protection of test parameters
  • Stepper motor-driven, producing smooth and quiet operation with no speed variation under load
  • USB output of force or force vs. travel
  • Compact footprint, suitable for crowded work benches
  • Ergonomic design, with smart, clean cable management
  • Integrated electronics assembly, easily removed and transported for service
  • Adjustable mounting plate with T-slot base

Optional Functions

Any of the below functions may be purchased at time of order or may be enabled in the field at a later date though a code activation process. The only exception is the AF009 travel measurement option, which also requires field hardware installation.

A complete options package is also available, including all of the below features at a discounted price.

The test stand is shipped in Demo Mode, during which time all available features are temporarily enabled for 160 hours of operation.

FeaturePart No.DescriptionRequirements
FollowMe®AF008Crosshead movement responds to manually pushing or pulling on the force gauge shaft or load cell. Increasing force produces greater speeds. Ideal for setups and quick positioning.

Included when ordering the ESM303-003 safety shield.
  • Model M7i or M5i indicator
  • 09-1252 interface cable
Travel indicationAF009Travel is indicated on the control unit display, with output via USB. An internal scale utilizing Renishaw technology produces significantly higher accuracy than with conventional rotary encoder-based designs. Backlash and nonlinearity are virtually eliminated.
  • Idata output to a PC is required, add 09-1252 and 09-1158 cables, and a Model M7i or M5i indicator.
  • Field activation requires hardware installation. Otherwise, hardware is factory installed at time of order.
Computer controlAF010

The ESM303 may be fully controlled by a PC through a custom-written program in any language supporting ASCII communications. Also responds to the legacy Chatillon TCD command set and legacy Nexygen TCD software (not available from Mark-10).

This option is not required for MESUR®gauge Plus software.

  • Model M7i or M5i indicator
  • AF009 travel indication option
  • 09-1252 interface cable
  • 09-1158 USB output cable

Programmable travel limitsAF011The stand stops at or cycles between programmable upper and lower travel distances.
  • AF009 travel indication option

Overload protectionAF012Protects a force gauge or force sensor against overload. Program the desired percentage of full scale of the gauge. Adjustable analog voltage setting allows the stand to interface with virtually any gauge with analog output.
  • Model M7i or M5i indicator with load cell
  • 09-1252 interface cable
Auto returnAF013The crosshead moves to a limit switch, force set point, travel position, or break, then stops and reverses direction at full speed to the opposite limit.
  • If reversing at force set point: Model M7i or M5i indicator with load cell, and 09-1252 interface cable
  • If reversing at travel limit: AF011 programmable travel limits option
  • If reversing at break: AF019 break detection option and 09-1252 interface cable

Cycling / dwell timeAF014Same as auto return, but with the ability to program up to 100,000 cycles. Programmable dwell time for right and left limits (set independently) can be set up for up to 10,000 seconds..
  • Same as auto return, at the same speed in each direction. Add AF016 for independent right and left speeds.
Independent Up and Down speedsAF016Configurable speeds for up and down directions.
Low speed extensionAF017Extends the standard speed range down to 0.02 in/min (0.5 mm/min).
High speed extensionAF018Extends the standard speed range up to 45 in/min (1,100 mm/min).
Break detectionAF019Crosshead stops at a sudden drop in force. Programmable percentage of peak force.
  • Model M7i or M5i indicator
  • 09-1252 interface cable
LoadholdingAF020Dynamically adjusts the crosshead position to maintain a programmed load for an indefinite or specified period of time.
  • Model M7i or M5i indicator
    If a specified time is required, add AF014 cycling / dwell time option
    09-1252 interface cable
Preload / sample touchAF021Stops the crosshead and/or zeroes the travel display at an initial preload – useful in tensile, compression, spring, elongation, and other applications. Preload is programmable as a percentage of force gauge/load cell full scale. Three modes: (1) stop, (2) stop and zero, and (3) zero without stopping.
  • AF009 travel indication
  • Model M7i or M5i indicator
  • 09-1252 interface cable

Specification

Load capacity:

300 lbF (1.5 kN) @ Up to 24 in/min (610 mm/min)
200 lbF (1 kN) @ > 24 in/min (> 610 mm/min)   

Speed range:

Standard:  0.5-13 in/min (13-330 mm/min)
Optional: 0.02 – 45 in/min (0.5 – 1,100 mm/min) 

Maximum travel18.0 in (457 mm)
Speed setting accuracy ± 0.2% of setting
Speed variation with load ± 0% [Stepper motor driven]
Limit switch repeatability 0.001 in [0.03 mm]
Travel accuracy *± 0.002 in. per 10 in. (±0.05 mm per 250 mm)
Travel resolution 0.001 in [0.02 mm]
PowerUniversal input 80-240 VAC, 50/60 Hz
Weight 62.5 lb (28.4 kg)

* Because load cell deflection and system deflection are present and not automatically compensated for, this equipment is recommended for applications requiring at least 0.2 in [5 mm] of travel distance.

 

Ordering Infomation

ModelDescription
Hardware
ESM303HMotorized test stand,110V*
AC1094-1Frame extension for ESM303H, 6″
AC1094-2Frame extension for ESM303H, 12″
AC1094-3Frame extension for ESM303H, 24″
ESM303-004-1Control panel tabletop mounting kit, ESM303H
09-1252Test stand-indicator interface cable, ESM303H
09-1158USB cable
AC1064Load cell hardware kit for ESM303
Controller Options
AF008FollowMe
AF009Travel measurement
AF010PC control
AF011Travel limits
AF012Overload protection
AF013Auto return
AF014Cycling
AF016Independent up/down speeds
AF017Low speed range extension
AF018High speed range extension
AF019Break detection
AF020Load holding
AF021Preload
AF022Save multiple profiles
AFCOMP-HComplete options package for ESM303H
* ESM303H contains a universal power supply (80 – 240V) and includes a power cord with US plug. Add suffix ‘E’ for Euro plug, ‘U’ for UK plug, or ‘A’ for Australian plug. Ex: ESM303HE

Power cords also available for purchase individually. 

 

เว็บไซต์นี้มีการใช้งานคุกกี้ เพื่อเพิ่มประสิทธิภาพและประสบการณ์ที่ดีในการใช้งานเว็บไซต์ นโยบายความเป็นส่วนตัวและคุกกี้